A packaging machine is a precision thermal and mechanical system. Film dust, a worn sealing tape, a loose belt or a slightly dry guide rail will quietly reduce seal quality and output long before anything actually stops. Ten small habits, done on a schedule, protect both uptime and pack quality.

Why preventive maintenance pays

There are three costs to a poorly maintained line: rejected packs (film, product and labour already spent), slower running (operators compensate for drift by reducing speed), and unplanned stops (the most expensive, because the whole upstream and downstream line waits). On an export-oriented factory, a leaking seal discovered after shipment is worse than all three.

Preventive maintenance also protects your warranty position and makes troubleshooting far easier: if temperature, tension and cleanliness are known-good, a fault is much more likely to be a specific component or a film lot. That is why we recommend logging the basics from day one.

Habits 1–4: every shift

1. Clean the sealing jaws and cross-seal area

Residue on the jaws is the number one cause of weak seals and burnt film. At the start and end of each shift, with the machine isolated and cool enough to work safely, remove film residue and product dust from the jaw faces, serrations and the fin-seal rollers. Use a soft brass or nylon brush, never a steel scraper on coated jaws.

2. Inspect the sealing element and PTFE tape

Check the heater element, thermocouple and the PTFE (Teflon) cover/tape for nicks, carbon build-up or uneven contact. Replace tape before it tears through; a damaged cover creates hot spots that show up as inconsistent seals across the pack width. This is a two-minute check that prevents hours of chasing "random" leakers.

3. Clear the film path and product infeed

Wipe forming boxes, collars, guide rollers and infeed guides. On a VFFS line, also clear powder from the forming collar and the seal-area guards; on a flow wrapper, clear crumbs from the infeed chain and the fin-seal wheels. Dust in the seal area is a film problem as much as a machine problem, see the film selection guide.

4. Verify temperature, pressure and the first packs

After warm-up, confirm the jaw temperature against the setpoint with an independent probe if available, then run ten packs and perform a simple seal check: squeeze test, peel test and, for liquids, a drop or inversion test. Record the result. Catching a 5 °C drift at 8 a.m. costs one minute; catching it at 4 p.m. costs a pallet.

Habits 5–7: every week

5. Check belts, chains and tension

Inspect film pull belts, infeed chains and conveyor belts for glazing, fraying and correct tension. A slipping pull belt changes bag length registration on VFFS and print position on flow wrap. Tension to the manufacturer's specification, not by feel, over-tensioning wears bearings and stretches film.

6. Check pneumatics and air quality

Drain the filter/regulator bowl, check for leaks at fittings, and confirm pressure is stable during a full cycle. Wet or fluctuating compressed air causes intermittent jaw and cutter faults that are notoriously hard to diagnose because they disappear when the line stops. If your plant air is humid, a dryer is a better investment than any spare part.

7. Lubricate to the schedule, and only to the schedule

Apply the specified lubricant to the points in the manual, cams, guides, chains and bearings, and wipe off excess. Over-lubrication attracts product dust and can contaminate film and seals. Keep food-grade lubricant where the machine is used for food packaging, and record the lubricant type and date.

Habits 8–10: every month

8. Inspect wear parts and cutting edges

Check cross-seal knives, serrated jaws, punches, vacuum cups/grippers on the premade pouch machine, and the rubber rollers on the fin seal. Dull knives tear film rather than cut it; worn vacuum cups cause pouch pick-up failures. Replace on condition, but inspect on a fixed date.

9. Verify sensors, coders and safety devices

Clean photo-eyes and registration sensors, confirm the print mark is being read consistently, check the date coder alignment, and test every emergency stop, guard interlock and light curtain. Safety devices are not optional maintenance items: they are the first thing an auditor will test.

10. Review recipes and back them up

For multi-SKU lines, review saved recipes against actual running parameters and export a backup of the controller configuration. Recipe drift after an operator "temporarily" adjusts temperature or bag length is a common, invisible source of quality variation. A backup also makes recovery after a controller replacement a ten-minute job instead of a two-day one.

A simple frequency table

FrequencyTasksTypical time
Every shiftClean jaws, inspect PTFE tape, clear film path, verify seals10–15 min
WeeklyBelts/tension, pneumatics, scheduled lubrication30–45 min
MonthlyWear parts, sensors, safety devices, recipe backup1–2 h
Every 6–12 monthsFull service, bearing/gearbox check, heater calibration, electrical inspectionHalf day

Print this table, laminate it, and put it on the machine. A checklist that lives in a folder is a checklist nobody uses.

Spare parts worth keeping in stock

  • Sealing elements / heater cartridges and thermocouples for each jaw.
  • PTFE tape or covers, and spare jaw serration inserts.
  • Cross-seal knives and the matching fixed blade.
  • Film pull belts, infeed belts and a set of drive belts.
  • Vacuum cups / grippers and solenoid valves for pouch handling.
  • Photo-eye sensors, registration sensors and a spare encoder cable.
  • Common bearings, fuses, relays and a spare HMI/control cable.

Ask your supplier which of these ship with the machine and which are consumables excluded from warranty. A modest spares kit turns a two-week wait for a part into a twenty-minute fix.

Build a 10-minute log

Keep one page per week with: date, operator, SKU, film lot number, jaw temperature setpoint, line speed, packs produced, rejects and the reason for any stop. After a month you will see patterns: a specific film lot, a particular SKU, or a drift that always appears after a Friday clean-down. That log is also the first thing a service engineer will ask for, and it shortens any remote support call dramatically.

Need a maintenance schedule for your model? Tell us which machine and film you run, and we will share a model-specific checklist and recommended spares list. Contact our engineers →

Five faults we get called about, and what causes them

The checklist above prevents most problems. When something does fail, the symptom usually points at one of five causes, and four of them are faster to check than a service visit.

Bags leak at the seal

Product in the seal area, jaw temperature drift, or worn PTFE tape. Check the tape first, then the thermocouple reading against a contact thermometer, then the fill timing. On powder lines, add a settle delay before the jaw closes.

Film wanders off centre

A roll wound unevenly, a stretched dancer roller, or product build-up on the forming collar. Re-thread the film before touching the photo-eye. Adjusting registration to compensate for a mechanical drift usually makes it worse.

Machine stops on a jaw fault

Almost always a product jam at the cross-seal or a dull cutting blade. Clear the jam, check the blade edge against a straight edge, and reset. Repeated jaw faults on the same product mean the fill is arriving late.

Weights drift outside tolerance

Product build-up in the weigher hoppers, or a load cell due for calibration. Clean the hoppers at every shift change and calibrate monthly. A drifting weight on one hopper only is a hopper problem, not a calibration problem.

Cartons jam at the leaflet folder

Paper weight or folded size outside the folder setting. Measure a sample with a calliper instead of trusting the nominal figure on the carton specification.

How often should the jaws be cleaned?

Every shift on dusty or sticky products, once a day on dry granular products. Use a brass brush and a lint-free cloth. Never scrape a jaw with a blade, because a scratched face will not seal evenly again.

Do I need a spare parts kit?

Yes for the parts that stop the line: PTFE tape, sealing elements, cutting blades, belts and a thermocouple. Those five items cover most unplanned stops, and they cost far less than a week of downtime.

Seal faults often start with the film rather than the machine. See the film guide, and when to automate if maintenance is eating the shift.

Frequently asked questions

At minimum at the start and end of each shift, and immediately after any film burn or product spill. Residue carbonises quickly and creates uneven seal pressure.
Product dust or liquid in the seal area, combined with a jaw temperature that has drifted out of the film's sealing window. Check cleanliness and verify temperature with an independent probe before adjusting anything else.
Heater elements, thermocouples, PTFE tape/covers, cross-seal knives, pull belts, vacuum cups/grippers, photo-eyes and common fuses/relays. These are low-cost and cover the majority of stoppages.
Daily and weekly tasks are designed for trained operators. Monthly electrical checks, heater calibration and controller work should be done by a qualified technician, with the power isolated and lockout applied.

Next step: tell us about your product or browse all packaging machines.