Flexible pouches have taken shelf space from cartons, cans and jars for good reasons: less material, lower freight weight, better print area and convenient reclosure. But "pouch" covers several quite different structures, and each one has implications for filling speed, sealing and machine choice.

Why pouch format comes first

A pouch is both a container and a marketing surface. Changing the format later usually means changing the filling machine, the film or pouch supplier, the carton dimensions and possibly the retail shelf plan. So decide the format before you request machine quotes.

There are two production routes. Form-fill-seal machines such as a VFFS make bags from a film roll, economical, fast and flexible on size, but limited to simpler shapes. Premade pouch machines such as the rotary PW-800 open, fill and seal ready-made pouches, slower and higher unit cost, but able to handle zippers, spouts, shaped outlines and high-quality rotogravure printing. This guide focuses on the premade route, where format choice matters most.

The five main pouch formats

1. Stand-up doypack

The bottom gusset opens so the pouch stands upright. It is the default for snacks, dried fruit, coffee, pet food, detergents and powders. It gives excellent billboard area and works with or without a zipper. On a rotary machine it is picked, opened by vacuum, filled through the top and sealed across the top, the most stable and fastest premade format.

2. Ziplock / resealable pouch

A press-to-close zipper is added near the top, above the final seal. Essential for multi-serve products (granola, nuts, cheese, pet food) where the consumer will not finish the pack in one sitting. The machine must open the zipper before filling, keep the zip area clean, and press it closed before sealing. Zipper detection and a "zip open" check are worth specifying.

3. Spout pouch

A welded plastic spout with a cap, usually at a top corner or centre. Used for liquids, sauces, purees, baby food, detergents and motor oil. Filling is done through the spout by a liquid or paste filler, so the dosing system, not the pouch handler, determines accuracy and speed. Spout pouches need strong seals around the weld and careful cap torque control.

4. Three-side / flat pillow pouch

Sealed on three sides, flat and light. Common for single-serve sachets, seasoning, condiments, medical dressings and samples. Lowest unit cost and fastest to run, but no stand-up presentation and no reclosure. Very high volumes are often better served by a VFFS or sachet machine rather than a rotary premade line.

5. Shaped / die-cut pouch

Custom outlines, rounded corners, contoured waist or a shaped window. Strong shelf differentiation for beverages, confectionery and cosmetics, and popular for children's products. Expect higher pouch cost, tighter registration requirements and slower machine speeds. Ask the pouch supplier for a machinability test on your specific rotary machine before committing to a large print run.

Format comparison table

FormatStand-upReclosableTypical fillingRelative speed
DoypackYesOptionalSolids, granules, powdersHigh
Ziplock pouchYesYesMulti-serve dry goodsMedium
Spout pouchYesCapLiquids, sauces, pastesMedium–low
Flat three-side sealNoNoSingle-serve, samplesVery high
Shaped pouchUsuallyVariesPremium retail, drinksLow–medium

Matching a format to your product

  • Dry free-flowing solids (nuts, snacks, granules): doypack or ziplock doypack; dose with a multihead weigher.
  • Fine or cohesive powders (flour, spice, milk powder, detergent): doypack with a zipper; dose with an auger filler and specify dust control at the seal area.
  • Liquids and viscous sauces: spout pouch with a piston or pump filler; check product viscosity and whether particulates are present.
  • Single-serve portions: flat three-side sachet; consider a VFFS/sachet line for volume rather than a rotary premade machine.
  • Premium gift or launch SKU: shaped pouch with registered printing, accepting a lower speed and higher unit cost.

The dosing system and the pouch handler must be specified together. A rotary pouch machine with eight stations is only as fast as the weigher or filler feeding it. If you are still weighing up the machine family itself, the flow wrap vs VFFS comparison explains where form-fill-seal still wins.

Barrier, filling and sealing considerations

Premade pouches are usually laminates: an outer print layer (PET or OPP), a barrier layer (EVOH, metallised PET or aluminium foil) and an inner sealant (PE or CPP). Match the structure to the product's oxygen and moisture sensitivity, then confirm the sealant's seal-initiation temperature is compatible with the machine's jaw temperature and dwell time.

Three practical points that cause most start-up problems:

  1. Seal-area contamination. Powder dust or liquid splash in the top seal causes leakers. Specify an anti-dust filling nozzle, settle time and, for liquids, a no-drip valve.
  2. Zipper and spout handling. Confirm the machine can open, detect and close the closure reliably at your target speed, and that the pouch magazine can feed the stiffer spout pouches without shingling.
  3. Residual oxygen / headspace. For sensitive products, ask about nitrogen flushing at the filling station and verify achievable residual oxygen with a test batch, not a datasheet claim.

Our film selection guide goes deeper on laminate structures, and the 5-step buying guide covers how to write all of this into a specification suppliers can actually quote against.

Common specification mistakes

  • Choosing a shaped or spouted pouch before checking it can run at the required speed.
  • Ordering printed pouches before a machinability test on the actual machine.
  • Forgetting that a zipper or spout adds a station and reduces net output.
  • Specifying a barrier laminate without confirming the sealant layer matches the sealing jaws.
  • Underestimating pouch magazine capacity and changeover time between formats.

Need a second opinion? Tell us your product, fill weight and target packs per hour. We will recommend a pouch format and a filling configuration, and can arrange a test run with sample pouches. Talk to an engineer →

Pouch format decides the filling system

Pouch shape is a marketing decision until you specify the machine. Then it becomes a mechanical constraint, because the opening, the fill path and the seal area are all different.

Spout pouch: liquid pump plus a spout station

The spout is welded into the pouch before filling and the product goes in through it. That rules out powders and chunky pieces. Expect 25 to 35 pouches per minute, a leak test after sealing, and a pouch specification that states the spout diameter and thread.

Zipper pouch: weigher or auger, plus a zipper opening station

A zipper profile has to be opened before filling and closed after. Powder in a zipper pouch needs a clean fill zone, otherwise powder lodges in the tracks and the zipper will not seal. This is the most common complaint on powder zipper lines.

Flat bottom pouch: weigher, and a slower cycle

The gusset must be opened squarely, which takes time. Flat bottom pouches look the most premium on shelf and run 20 to 40 pouches per minute. They also use more film per pack than a doypack of the same volume.

Which pouch type is cheapest per unit?

A flat or stand-up pouch with a plain top seal. Zippers, spouts and shaped pouches add material and converting steps, and shaped pouches waste more film in die cutting. Pouch cost often exceeds the saving in film yield, so price the pouch per thousand before choosing the format.

Can one machine run doypack and flat bottom pouches?

Sometimes, with different gripper sets and a recipe. Ask for both formats to be demonstrated on the machine you are buying, not on a sister model, and ask what the changeover takes in minutes.

Film structure matters as much as pouch shape. See the packaging film guide, or read how to choose a packaging machine.

Frequently asked questions

A rotary premade pouch machine can usually handle doypacks, ziplock pouches and three-side-seal pouches with adjustable grippers and recipes. Spout pouches and heavily shaped pouches often need dedicated feed and handling parts, confirm compatibility before ordering.
Yes, the premade pouch itself costs more per unit because it is converted and printed offline. In exchange you get better shelf presentation, reclosure options and shaped formats. Compare cost per 1,000 saleable packs for your volume.
Liquids and sauces are usually dosed with a piston, pump or flow-meter filler through the spout. Viscosity and particulates determine the valve type; ask for a test with your actual product.
Use an auger filler with dust extraction, a nozzle that reaches into the pouch, a short settle time before sealing, and jaw designs that tolerate light contamination. A sample test on your own film is the only reliable confirmation.

Next step: tell us about your product or browse all packaging machines.